SPECTRAL AND DEFORMATION ANALYSIS OF SYSTEMS "VESSELS - REINFORCEMENT" OF VERTICAL SHAFTS

UDC 622.674:539.3:535.33

Authors:

Ilyin S.R., Ph.D. (Tech.), Senior Researcher

(IGTM NAS of Ukraine)

Dubinin M.V., M.Sc. (Tech.)

(RIMM)

Abstract.

With the growing the life of shafts the problem to ensure safety lifting vessels in a Hard armor (due to increased wear of shaft equipment, curving shafts axes under the influence of geological and mining-technical conditions while maintaining a sufficiently high performance requirements mine hoist.

By the method of finite element modeling obtained amplitude-frequency and deformation parameters of the most common hard armor schemes and skips designs by modern domestic coal producers. Based on these results was analyzed the minimum overlap of the side surfaces of the leading device. The results show that at invariable level of the dynamic loads (dynamic track width) the risk getting out of gearing of the vessel increases in proportion to the head-wear leading devices and streaks, which leads to an increase in total frontal gap and decrease the overlap region of the streak side surfaces by the walls of  the leading device.

Keywords: rigid reinforcement, mining shaft, box-shaped conductor, a weld, the radius of the rounded conductor, the dynamic deflection of the conductor.

References:

1. Płachno, M. (2005) “New approach to the design of shaft steelwork”, Mining sciences 50, Issue 4, pp. 465-496.

2. Vorobel, S.V., Trifanov, G.D. and Knyazev, A.A. (2007) “Dynamic Survey rigid reinforcement shafts Problems of the integrated development of mineral deposits in the Perm region”, Materialy krayevoy nauchno-tekhnicheskoy konferencii studentov, aspirantjv I molodykh uchenykh [Materials the edge scientific and technical conference of students, graduate students and young scientists], Perm Publishing House of Perm State Technical University, Perm, RU, 2007, pp. 195 – 201.

3. Hansel, J., Kawka, G.and Plachno, M. (1985) “An estimation of mine conveyance guiding”, Mechanika. - Tom 4 - Zeszyt 2.- Wydawnictwo AGN, Krakow, pp.115-128.

4. Dvornikov, V.I. and Dubinin, M. V. (2014), “Finite element modeling for stress-strain state of the mine trunks reinforcement that it has been made shaft skip”, Perm national research polytechnic university, Mining Electrical Engineering, pp. 55-60.

5. State committee of Ukraine on industrial safety, labour protection and mountain supervision (2010), 10.0-1.01-10. Pravila bezpeki u vugilnich shakhtakh [10.0-1.01-10 Rules of safety in coal mines], State committee of Ukraine on industrial safety, labour protection and mountain supervision, Kiev, Ukraine.

6. Ilyin, S. R., Solomencev, K. A. and Vasylkevych, V. I. (2014) “Analysis of the influence of the form of box-shaped cross-section streak rigid reinforcement shafts on permissible speed of hoisting vessels”, Geo-Technical Mechanics, no. 120, pp. 265-275.

7. Metodika raschyeta zhyestkikh armirovok vertikalnykh stvolov shakht [Method of calculating the rigid reinforcement vertical shafts] (1994), M.M. Fedorov Research Institute of mining mechanics (ed.), Donetsk, Ukraine.

8. Ilyin, S. R. (2010) “The experience of dynamic apparatus control and estimation of exploitation system safety “vessel – reinforcement” of vertical mining shafts”, The International Journal of transport & logistics, pp.395-403.

9. Ilyin, S. R. and Trifanov, G.D. (2009) “Dynamic diagnostics of systems "vessel - reinforcement" vertical shafts”, Mining Equipment and Electromechanics, no. 8, pp. 29 - 34.

About the authors:

Ilyin Sergii Rostislavovich, Candidate of Technical Sciences (Ph.D), Senior Researcher, M.S. Polyakov Institute of Geotechnical Mechanics under the National Academy of Sciences of Ukraine (IGTM, NASU), Dniepropetrovsk, Ukraine, Этот адрес электронной почты защищен от спам-ботов. У вас должен быть включен JavaScript для просмотра.

Dubinin Mikhail Valerievich, M.S. (Tech), Researcher, M.M. Fedorov Research Institute of Mining Mechanics (RIMM), Dоnetsk, Ukraine